Featured Products

POWER SUPPLY INTERIOR PERFORATED 12V 6A 72W
POWER SUPPLY INTERIOR PERFORATED 12V 6A IP20 CE100-240V   Input voltage: 100-240VAC Ouput voltage:12V DC Ouput current:6A Ouput power:72W size:110x78x36 mm(L*W*H) &nbs...
POWER SUPPLY INTERIOR PERFORATED 12V 6A IP20 CE100-240V
 
Input voltage: 100-240VAC
Ouput voltage:12V DC
Ouput current:6A
Ouput power:72W
size:110x78x36 mm(L*W*H)
 
This Power Supply includes a heat dissipating fan that will only come on when needed, reducing noises from the unit.
 
Technical Data:
Input
- Voltage: AC100-240V (range selectable by switch)
- Frequency: 50/60hz
 

Output:
- Working Voltage: DC12V (Constant voltage output, to ensure the stability)
- Working Current: 6A
- Electric Consumption: 75W
 
 
Built-in constant current limiting circuit 
100% full load burn-in test
 
Voltage Protection: Integral Short Circuit, Overload, Over Voltage - it will shut down the unit in case of faults and Overloads to protect the unit and connected equipment from damage.
Shock and Vibration resistant

With air cooling: It works automatically according to the temperature (Forced air cooling by built-in DC fan)
Built-in cooling Fan ON-OFF control 
Low working temperature with long life.

Shell Material: Aluminum
 
Requires power cord (not included). To use this adapter with a wall outlet, you must have an AC power cable.
 
Wiring:
AC Input :
L: Possitive (Brown or Red)
N: Negrative (Blue or Black)
Ground: Green & Yellow or Green
DC Output:
+V: LED´s Positive
-V: LED´s Negative
 
 
From
$
Qty.
Wall washer Light, 36W Input: DC12V RGB SMD5050, 70Lm/W ≥70Ra CE
Este bañador está compuesto por 24 LEDs de 1,5W de potencia cada uno. Debe ser conectado a 12V. Está montado sobre una barra de aluminio rígida y colocada dentro de un artefacto cuyo grado de protección ...
Este bañador está compuesto por 24 LEDs de 1,5W de potencia cada uno. Debe ser conectado a 12V. Está montado sobre una barra de aluminio rígida y colocada dentro de un artefacto cuyo grado de protección es IP66. Cada LED tiene un ángulo de apertura de 140° y vienen con las lentes colocadas, las mismas son de 30º cada una. Este tipo de luminaria es ideal para lograr efectos lumínicos en los exteriores, se utilizan generalmente para realizar bañados de luz sobre frentes, en pubs, restaurants, hoteles, discotecas, etc.  También se puede lograr el efecto de “cortina de luz” en una ventana.
 
 
From
$
Qty.
Wall washer Light, 36W Input: DC12V 3000mA, Cold white(5700-6500K), SMD3030, 36PCS. 70Lm/W ≥70Ra CE
Este bañador está compuesto por 36 LEDs de 1W de potencia cada uno. Debe ser conectado a 12V. Está montado sobre una barra de aluminio rígida y colocada dentro de un artefacto cuyo grado de protección es IP6...

Este bañador está compuesto por 36 LEDs de 1W de potencia cada uno. Debe ser conectado a 12V. Está montado sobre una barra de aluminio rígida y colocada dentro de un artefacto cuyo grado de protección es IP66. Cada LED tiene un ángulo de apertura de 140° y vienen con las lentes colocadas, las mismas son de 30º cada una. Este tipo de luminaria es ideal para lograr efectos lumínicos en los exteriores, se utilizan generalmente para realizar bañados de luz sobre frentes, en pubs, restaurants, hoteles, discotecas, etc.  También se puede lograr el efecto de “cortina de luz” en una ventana.

From
$
Qty.
LED 10mm blanco frio
The 10mm Ultra Bright LEDs are encapsulated in a transparent resin dome. How To Use: Below the dome there are two extended legs: the longer leg is the positive polarity, called anode and the shorter leg is the negative polarity, called ...

The 10mm Ultra Bright LEDs are encapsulated in a transparent resin dome.

How To Use:
Below the dome there are two extended legs: the longer leg is the positive polarity, called anode and the shorter leg is the negative polarity, called cathode. These legs indicate the way in which the LED should be connected to the circuit.

These LEDs can be used in three different ways:
- Individual: LED power directly from the power supply, either by means of a regulated supply, or with the use of resistors or regulators. It must supply the LED the desired voltage in work values.
- Parallel configuration: Powering a group of LEDs connecting all of the anodes together and all of the cathodes together, using the required tension regulated by a single resistor in series.
- Series configuration: powering a group of LEDs connected sequentially. The number of LEDs used for series is limited by the voltage delivered by the power supply. In most cases a resistor is required to compensate for voltage differences per series of LEDs. Various parallel series can perform using the same power source.

Polarization: the positive pole of the power supply must be connected to the anode, the longer leg (or the beginning of the series), while the negative pole must be connected to the cathode, the shorter leg (or the end of the series).

Use: They can be used for lighting, signage, traffic lights, flashlights, signaling devices, information panels, medical equipment, lighting of liquid crystal displays of mobile phones, calculators, PDAs, printers, bicycles, and more.

Technical Data

Beam Pattern: 30 º

Working Current: 20mA

Working Voltage: Power Supply Recommendations:

- DC3.1V @ 20mA:
   - Voltage min. Power:  DC2.8V
   - Voltage max. Power: DC3.6V

Luminous Intensity: 7.000-10,000mcd

Suggestion: If you need to adapt the LED to a small space, you can cut the legs using common scissors without compromising installation conditions.

Also: If you have a smaller space, you can use the 1.8mm, 3mm or 5mm Ultra Bright LEDs.

Attention: The Operating Voltage of this product is DC; never connect it to AC directly.

For optimum performance, do not exceed maximum load and the Power Supply should be 20% (approx.) stronger (Amps) than the total required to run your system.

Don’t forget to buy the following:

-constant current resistors ,

-power supply (We recommend DC3.3V @ 20mA ),

-LED holder.

All specifications are subject to change without notice

From
$
To $
Qty.
LED 10mm blanco frio
LED 10mm blanco frio
From
$
To $
Qty.
LED Driver 580mA 9-18Vcc 100-264Vca IP65
Este Driver es ideal para la conexión de LEDs High Power de 3W, se pueden conectar de 2 a 5 LEDs o bien de 1 a 2 LEDs de 5W. ...

Este Driver es ideal para la conexión de LEDs High Power de 3W, se pueden conectar de 2 a 5 LEDs o bien de 1 a 2 LEDs de 5W.

From
$
Qty.